The device from the rack, playing hair rollers, active body, passive institutions, structures composed of tightening screw up. The machine uses a chain drive to drive into the pig's head hit the track hair, hair tube by adjusting the distance between the fight to control the pig's hair to fight the case.
Main purpose: pig planing machine mainly for pig hair to play hair treatment, by the pig hanging in the transmission chain of the cone into the body to fight hair, hair of the pig to play and shower, to complete the pig plane hair.

Scope and working conditions: This product is applicable to any size and variety of pig, adapted to the temperature -25 ° C ~ 40 ° C, no fire, explosion hazard and corrosive media environment, apply power to exchange three phase, 50HZ, 380V.

Main technical parameters:

Product Power :2-2 .2 KW roller speed: 170r/min

Transmission Speed: 3m/min capacity: 360 / h

Dimensions: 3700x1800x1850mm Product Weight: 1200Kg

Model: BZT-00 type

Transmission structure and working principle

Main transmission part: two motors are driven by roller chain sprocket for rotating the opposite direction. According to local pig size and shaving cases, two rollers may be appropriate to adjust the center distance.

Propulsion components: the traction gear sprocket chain and pig by positioning seat rail rack meshing with the gear, traction pig bearing in rotation, move.

Installation and commissioning

A. pig hair planing machine shipped to the installation location, follow the packing list and acceptance, and carefully check for damage during transport, loss of parts of;

B. read the manual and other random files, to understand the structure of the product.

C. understand the installation site, ready to install facilities.

D. Gross planing machine placed the pig smooth, connected pipes, installation of power, all electrical circuit electrical installations, control circuit resistance to ground not less than 1000 ohms per volt operating voltage.

Turn on the power button, the pig's head outside the planing machine in working condition hair, check whether the smooth movement of the body, compact. The no-load test, without exception, before the load test.

Safe operation points

1) is to ensure that pig pig hot good quality shaving a prerequisite, so hot scraping continuous, uniform pig should be hot, hot enough or hot against the old and so on. Socket should be inserted through the pig's pig nose eyes to toggle pig rotation.

2) The aircraft wheel and chain guide are correct relative position is to ensure the normal operation of one of the keys in the rail imports, if there dead pull plug pig skew wheel can be adjusted to import the chain wheel and the rail is relatively appropriate location.

3) the early use of aircraft, because of hard rubber, leather, the case should be based on the first plane, the appropriate uniform remove some rubber shavings, or it may break pig.

4) Note leaching water to be poured 60 ° C ~ 62 ° C hot water, rail which should always wash with water.

5) The operator should have knowledge of mechanical and electrical operations, physical health;

6) The operator should be familiar with pig hair planing machine structure, performance, safety procedures and the instructions, etc.;

7) the operator to go through job training, certificates;

8) the operator safety, good protective measures;

9) class daily inspection before operation;

10) the use of any abnormal noise, shall comply with the first stop, after checking, troubleshooting and then drive to use;

11) the user must establish the necessary rules and regulations and safety procedures.

Inspection, maintenance and maintenance

The devices have been tested before commissioning the factory, but after leaving the factory may be due to transport equipment

Imbalance caused by factors such as discharge or failure, it is necessary to conduct a comprehensive inspection of the machine, in determining good everywhere, before installation.

After installation of the machine, pay attention to the bearing is normal, the chain tension is appropriate, whether part of the lubricating oil, in addition to normal maintenance, should be regularly adjusted by the tightness of the chain tensioning device, after the production season each year to conduct a major overhaul , excessive wear and tear of parts should be replaced to ensure the normal operation of the machine.

Maintenance: During the inspection, which do not meet the requirements should be an immediate repair, adjust or replace parts.

1) maintenance replacement parts and raw materials, performance should be the same;

2) pig hair planing machine in working condition, and not to carry out maintenance and repair.

Main wearing parts: chain, shaving board, with vertical seat, spherical ball bearings Z90513, bearing Z90511, bearing 209